886.18zł
Thermaltake Triple Racing Monitor Stand Pro is a steel triple screen frame offered in Black or Snow White. It supports three monitors weighing up to 20 kg each, with curved panels up to 32 inches or flat displays up to 34 inches. Five height settings and broad VESA support help align the picture with the cockpit. Browse other TV and monitor stands.
You might also like
Thermaltake Triple Racing Monitor Stand Pro creates an independent display section for one, two or three screens. It does not need to be bolted to the wheel and pedal chassis, so viewing distance can be adjusted separately from the seat. This makes it easier to bring the centre monitor close to the steering axis and build a panoramic view around the driver.
A free-standing layout is also useful with a high-torque Direct Drive wheelbase or motion system. The monitors do not share the same frame as the equipment producing force and vibration, helping the image remain calmer. The triple screen stand can surround a suitably sized cockpit. Thermaltake specifically lists its GR500 and a setup using the GM5 3DOF motion system as compatible combinations.
In a triple screen configuration, Thermaltake Triple Racing Monitor Stand Pro accepts three curved monitors up to 32 inches or three flat displays up to 34 inches. Each mounting position can carry a monitor weighing no more than 20 kg. For a single-screen setup, Thermaltake lists 27 to 55 inches, while its dual-screen recommendation states a 55-inch display size.
Diagonal size is only one part of compatibility. Check the monitor weight without its factory stand and confirm the rear mounting pattern before ordering. Supported standards are VESA 75 × 75, 100 × 100, 200 × 100, 200 × 200, 300 × 200 and 400 × 200 mm. This range covers conventional gaming monitors and larger panels with wider mounting points.
The monitor beam can be installed at 920, 970, 1020, 1070 or 1120 mm. These five settings help align the image with the driver's eye line, seat position and wheelbase height. Angle adjustment reaches 60 degrees, and the side sections can fold backwards when easier cockpit access or a narrower temporary footprint is needed.
Begin the installation with the centre screen and level it before adding the side monitors. Their distance and angle can then be matched to the central panel. This approach makes bezel alignment and a consistent horizon easier to achieve. If the simulator frame is still being selected, compare the current sim racing cockpits available from Simline.eu.
Thermaltake Triple Racing Monitor Stand Pro is offered on this page in two colour variants. Black model GSC-MSP-MDSLBB-01 has a fine-textured dark coating. Snow White GSC-MSP-MDSLWH-01 uses a light finish that can match a white cockpit, monitor housings or a flight simulator. Colour does not change load capacity, VESA support or adjustment.
The structure is made from powder-coated steel. Its arms use 1.5 mm cold-rolled sheet steel, while the main and extension columns have a diameter of 35 mm. Allow room for side displays, cables and access to VESA screws during installation. Monitors, the cockpit and other hardware shown as part of a complete simulator are sold separately.
In a triple screen configuration, Thermaltake Triple Racing Monitor Stand Pro accepts three curved monitors up to 32 inches or three flat displays up to 34 inches. Each mounting position can carry a monitor weighing no more than 20 kg. For a single-screen setup, Thermaltake lists 27 to 55 inches, while its dual-screen recommendation states a 55-inch display size.
Diagonal size is only one part of compatibility. Check the monitor weight without its factory stand and confirm the rear mounting pattern before ordering. Supported standards are VESA 75 × 75, 100 × 100, 200 × 100, 200 × 200, 300 × 200 and 400 × 200 mm. This range covers conventional gaming monitors and larger panels with wider mounting points.
In a triple screen configuration, Thermaltake Triple Racing Monitor Stand Pro accepts three curved monitors up to 32 inches or three flat displays up to 34 inches. Each mounting position can carry a monitor weighing no more than 20 kg. For a single-screen setup, Thermaltake lists 27 to 55 inches, while its dual-screen recommendation states a 55-inch display size.
Diagonal size is only one part of compatibility. Check the monitor weight without its factory stand and confirm the rear mounting pattern before ordering. Supported standards are VESA 75 × 75, 100 × 100, 200 × 100, 200 × 200, 300 × 200 and 400 × 200 mm. This range covers conventional gaming monitors and larger panels with wider mounting points.
The monitor beam can be installed at 920, 970, 1020, 1070 or 1120 mm. These five settings help align the image with the driver's eye line, seat position and wheelbase height. Angle adjustment reaches 60 degrees, and the side sections can fold backwards when easier cockpit access or a narrower temporary footprint is needed.
Begin the installation with the centre screen and level it before adding the side monitors. Their distance and angle can then be matched to the central panel. This approach makes bezel alignment and a consistent horizon easier to achieve. If the simulator frame is still being selected, compare the current sim racing cockpits available from Simline.eu.
Thermaltake Triple Racing Monitor Stand Pro is offered on this page in two colour variants. Black model GSC-MSP-MDSLBB-01 has a fine-textured dark coating. Snow White GSC-MSP-MDSLWH-01 uses a light finish that can match a white cockpit, monitor housings or a flight simulator. Colour does not change load capacity, VESA support or adjustment.
The structure is made from powder-coated steel. Its arms use 1.5 mm cold-rolled sheet steel, while the main and extension columns have a diameter of 35 mm. Allow room for side displays, cables and access to VESA screws during installation. Monitors, the cockpit and other hardware shown as part of a complete simulator are sold separately.
| Technical specification - Thermaltake Triple Racing Monitor Stand Pro | |
|---|---|
| Product variants | |
| Black variant | Fine-textured black coating, P/N GSC-MSP-MDSLBB-01 |
| Snow White variant | Fine-textured white coating, P/N GSC-MSP-MDSLWH-01 |
| Displays and load | |
| Supported number of displays | 1, 2 or 3 |
| Three curved monitors | Up to 32 inches each |
| Three flat monitors | Up to 34 inches each |
| Single-display configuration | 27 to 55-inch monitor |
| Dual-display configuration | Thermaltake lists a 55-inch display size |
| Maximum load | 20 kg per display, up to 3 × 20 kg |
| Installation and adjustment | |
| VESA patterns | 75 × 75, 100 × 100, 200 × 100, 200 × 200, 300 × 200, 400 × 200 mm |
| Height settings | 920, 970, 1020, 1070 and 1120 mm |
| Angle range | Up to 60° |
| Side-section folding | Can be folded backwards |
| Construction | |
| Material | Powder-coated steel |
| Arm thickness | 1.5 mm cold-rolled steel sheet |
| Column diameter | 35 mm |
| Listed compatibility | Thermaltake GR500 and a setup using the GM5 3DOF motion system |
No. Both variants use the same steel structure, adjustment range, VESA patterns and load rating. Their coating colour and product number are the only differences.
The stand can be used with one, two or three monitors. Its full structure provides a central display position and two adjustable side sections.
Thermaltake specifies three curved displays up to 32 inches or three flat monitors up to 34 inches. Each panel must remain within the 20 kg limit and use one of the supported VESA mounting patterns.
Yes. Thermaltake lists a range from 27 to 55 inches for a single display. Its weight and rear mounting pattern must still meet the stand's load and VESA requirements.
The limit is 20 kg for each display position. A triple-monitor arrangement can carry 60 kg in total, provided no individual mount exceeds its own 20 kg rating.
The stand supports 75 × 75, 100 × 100, 200 × 100, 200 × 200, 300 × 200 and 400 × 200 mm. Also check the shape of the rear housing and cable access after the mounting plate is installed.
Yes. The beam can be set at 920, 970, 1020, 1070 or 1120 mm. Choose the position according to seat height, driving posture and the centre screen's location behind the steering wheel.
Thermaltake lists the GR500 and a setup using the GM5 3DOF system as directly compatible. Since the stand is self-supporting, it can also surround another cockpit when the frame width and available floor space do not interfere with its structure. Browse other sim racing cockpits.
No. This product is the mounting structure. Monitors, the cockpit, motion equipment and other hardware shown in complete simulator images are separate products.
Black blends with most dark cockpits and monitor housings. Snow White suits a light simulator, white frame or flight setup. Technical specifications are identical, so the overall appearance can guide the decision.
You might also like
English 
Polski
